Categories

Newsletter

DJI F550 + NAZA-M V2 + ZUNMUSE H3-2D + AURORA9 Including the full set

DJI F550 + NAZA-M V2 + ZUNMUSE H3-2D + AURORA9 Including the full set

DJI F550 + NAZA-M V2 + ZUNMUSE H3-2D + AURORA9 Including the full set

More details


$1,600.00 tax incl.

16 other products in the same category:

Overview

Flame Wheel 330/450/550 is a series of multi-rotor flying platform designed for all pilots for entertaining or amateur AP. With DJI WooKong-M or NAZA autopilot system, such actions as hovering, cruising, even rolling and other maneuvers can be achieved. It can be applied to entertainment, aerial photography, FPV and other aeromodelling activities.

 

 


Features

  • Ultrastrength material
  • Integrated PCB wiring
  • Huge assemble space
  • Gorgeous Frame Arms

 

Ultrastrength Material

Frame Arms adopt PA66+30GF ultrastrength material design, provide better crashworthiness.

 

Integrated PCB Wiring

Using high strength compound PCB frame board, which makes wiring of ESCs and battery more safe and easier.

 

Huge Assemble Space

Optimized frame design, which provides abundant assemble space for autopilot systems.

 

Gorgeous Frame Arms

Provide different color frame arms: red, white, black, which makes your flight more colorful.

 

No longer need to worry airframe damage caused by not Tremendous strength of the frame relieves concerns of damage caused by the crash.

 Quad Copter novice users can easily enjoy flying and DJI NAZA Multi-Copter Automatic leveling device to maintain altitude and fitted as standard and a manual mode for the Fun Fly (leveling) RC Mode of Tasmanian change to the fast-paced and the thrills that you can enjoy the flight.

NAZA Controller (MC), as well as Quad Copter Hex type of helicopter as two port settings and camera control of pan, tilt, horizontal jimbeo can separate fitted.

Helicopter crash caused by the use of excessive current only for the NAZA NAZA kit specially designed current stabilizer (VU) is built into the phenomenon, or at least work can be avoided. Gas flying through the mode select and identify the status of the LED attached to a stabilizing device connected to a computer using the USB interface controller settings and firmware upgrade can proceed.

 

- NAZA-M V2

 

 

 

All-in-one Design

DJI adheres to continuous innovation and improvement. With the new firmware, new attitude stabilization algorithm and optimized hardware structure, the Naza-M V2 provides better flight performance. The innovative All-in-one design simplifies installation and saves space and weight. It contains inner damping, controllers, 3-axis gyroscope, 3-axis accelerometer and barometer in its light and small Main Controller. It can measure flying altitude and attitude and therefore can be used for autopilot/automatic control.

All-in-one Design
 

Independent PMU with amazing function extension

The Naza PMU V2 has enhanced BEC functionality and provides extendable CAN BUS ports, which can support iOSD, Zenmuse H3-2D gimbal (pitch control). Support is also included for optional Bluetooth LED module to allow parameter adjustment via a mobile APP (future firmware upgrade required for this functionality)

Independent PMU with amazing function extension
 

Advanced & Improved Attitude Stabilization Algorithm

The latest fourth generation attitude stabilization algorithm not only inherits the outstanding flight stability of DJI products, but also provides excellent maneuverability even without the GPS module. It is more flexible and stable, and gives the hobbyists a wonderful flight experience. New features have been included such as GPS course automatic compensation, GPS & Compass sensor calibration, new take-off mode and so on.

Advanced & Improved Attitude Stabilization Algorithm
 

Nine Types of Multi-rotors Supporte

Naza-M V2 now supports nine types of multi-rotor, which meets the different needs of the enthusiasts.
Quad I, Quad X;
Hexa I, Hexa V, Hexa Y, Hexa IY;
Octo X, Octo I, Octo V; ( Naza-M V2 does not support the aircraft which has large vibration, so when you choose to use hexa-rotor or octo-rotor, please use the vibration dampening devices accordingly.

Nine Types of Multi-rotors Supported
 

Multiple Flight Control Modes/Intelligent Switching

It offers three types of control modes: GPS Atti. Mode (with GPS module), Atti. Mode, Manual Mode. The pilot can switch between the three modes to achieve different flight characteristics. It also can adjust automatically within the flight environment and intelligently switch between GPS Atti. Mode and Atti. Mode to make sure the flight is safe and secure. In the software at the position of the manual mode you can choose manual, attitude or failsafe; it supports one key failsafe trigger.

Multiple Flight Control Modes/Intelligent Switching
 

GPS Module Available/Accurate Position Hold

The plug and play GPS module will greatly enhance the performance for Aerial Photography with accurate Position Hold, Return-To-Home and Intelligent Orientation Control functionalities. With the GPS Module, the multi-rotor will have position and altitude locked accurately even in windy conditions. Hovering accuracy is approximately 2.5m horizontal and 0.8m vertical.

GPS Module Available/Accurate Position Hold
 

Intelligent Orientation Control

Usually, the forward direction of a flying multi-rotor is the same as the nose direction. By using Intelligent Orientation Control (IOC), wherever the nose points, the forward direction has nothing to do with nose direction:
In course lock flying, the forward direction is the same as a recorded nose direction. See the following figures(Mode 1):

In home lock flying, the forward direction is the same as the direction from home point to multi-rotor. See the following figures (Mode 2):

 Intelligent Orientation Control
 

Enhanced Failsafe Mode

If your transmitter supports failsafe, then you can set failsafe through port-U. Naza controller has built-in auto level failsafe function, which means when the communication between MC and the transmitter is disconnected, the outputs of all command sticks from controller will go to center position. If the GPS module is used, you can also set RTH on failsafe. If your transmitter has only 4 channels, then MC will work in Atti. Mode by default without the failsafe function.

Enhanced Failsafe Mode
 

Two Levels of Low Voltage Protections

In order to prevent your multi-rotor from crashing or other harmful consequences caused by low battery voltage, we have designed two levels of low voltage protection. You can choose not to use this, however we strongly recommend you to enable the protection. Both levels of protection have LED warning as default. The first level will blink the red light continuously; the second level will blink red light continuously and the multi-rotor will descend and land. In manual mode when low voltage protection is triggered the LED warning will be active only.

Two Levels of Low Voltage Protections
 

Motor Arm and Motor Dis-arm

There are four ways to start the motors, see the following picture:

When you want to start the multi-rotor, you need to perform any of the ways of CSC. During the flight, if the motors stop, you can immediately execute the CSC and the motors will start. This enhances the safety of the multi-rotor; no uncontrolled starting of the motors.

Motor Disarm: There are two modes of Motor Disarm: namely Intelligent Mode and Immediate Mode. For more information, please refer to the user manual or DJI Wiki.

Note: It has a brand new, smoother take-off algorithm, which is more stable and provides a brand-new experience in supporting double spring TX; every time you let go of the throttle stick it will hover.

Motor Arm and Motor Dis-arm
 

PPM, S-BUS & Ordinary Receiver Supported

Minimum Four channel receiver supported, also PPM and Futaba S-Bus receiver supported. PPM & S-Bus receivers (the general use of the first 8 channels of S-Bus receiver) to optimize the channel connection, the A, E, T, R, U five-channel functions are set using channel X2, use only one servo cable to connect the PPM or S-Bus to X2, this makes installation quick and easy.

PPM, S-BUS & Ordinary Receiver Supported
 

Independent LED Module

The Independent LED module makes the indication of the flight status and the system status to the ground much clearer. The pilot can get information more quickly and more conveniently, even at night, he/she can get real-time flight information feedback through the LED flashing frequency and colour. In addition, the module has a USB interface, which is used for parameter settings and firmware upgrade.

 Independent LED Module
 

Built-in Gimbal Stabilization Function

The gimbal stabilization module is compatible with almost all 2-axis gimbal systems. The system will adjust the gimbal and camera according to the attitude of the aircraft after setting the parameters the first time.

Built-in Gimbal Stabilization Function
 

Multi-rotor One-power Output Fail Protection

In most conditions, the whole multi-rotor will retain good attitude and rotate around the frame arm with no power output, due to imbalanced mechanical structure and external environment. Rotating is mainly caused by payload and external environment. When payload is heavier, rotating speed is faster. On rotating, the hexa-rotor physical structure can cause rudder to become out of control. This humanistic protection function from Naza-M V2, in Attitude or GPS Mode, keeps attitude under control even with any one power output failed and highly reduces crash risk.

Multi-rotor One-power Output Fail Protection
 

Remote Gain Adjustment

The default parameter settings are preset for you to achieve a normal flight, and also supports remote parameter adjustment by using a control slider on the TX during flight in order to obtain better performance.

Remote Gain Adjustment
 

New Assistant Software & Firmware Online Update

The user interface of the assistant software has been comprehensively updated and brings you a new interaction experience. Instructions will automatically appear which is very convenient. In addition, on the left side of each menu section there is additional information. The logical design makes your parameter settings more simple and convenient. Like other DJI products the Naza-M V2 firmware can be upgraded free online.

New Assistant Software & Firmware Online Update

 

- ZUNMUSE H3-2D

 

2-AXIS Professional Gimbal With High Performance

The DJI ZenmuseH3-2D Gimbal is another milestone in gimbal innovation, which is designed for the GoPro Hero3. With its high precision, high stability, lightweight, plug and play features, it is widely used in film and television productions, advertising aerial photography, etc. Even if the aircraft is in high-speed flight, it can still stabilize and control the GoPro camera precisely with the highest stability. The precision of control angle is within the range of ±0.08°, so picture or video output can reach the best quality.

2-AXIS Professional Gimbal With High Performance
 

Easy to install, Plug and Play

No additional manual adjustment required, no need to adjust the C.G. or parameters in the software. In addition, the installation process is extremely simple and the plug-and-play characteristics make it easy for users to experience the performance of the H3-2D.

Easy to install, Plug and Play
 

Customized for GoPro Hero3

The H3-2D gimbal is designed for the GoPro Hero3, and remote start/stop shooting, video transmission (video downlink required), etc of the GoPro Hero3 will be supported by future firmware upgrades.

Customized for GoPro Hero3
 

Compatible with DJI flight control systems

The H3-2D gimbal is compatible with DJI flight control systems, it can adjust the roll and pitch angle according to the accurate control of the Gimbal feedback and communicate with the MC in real-time.

  • It supports WooKong-M, NAZA-M V1, NAZA-M V2, Phantom;
  • It will support Ace One, WooKong-H, NAZA-H;
  • It doesn't support NAZA-M LITE.

 

Notice: NAZA-M V1 and Phantom users need the PMU of NAZA-M V2.

Compatible with DJI flight control systems
 

The Core Technology Inherited from the Zenmuse

The H3-2D gimbal inherited the core algorithm from the Zenmuse Z15 gimbal and the unmanned aircraft flying attitude stability control algorithm. Combined with the high precision sensors and brushless motors, the DJI Zenmuse H3-2D gimbal provides pixel level stabilized footage.

The Core Technology Inherited from the Zenmuse
 

Independent IMU module

The independent high-precision IMU module provides precise attitude data and the closed-loop control gives improved control accuracy.Without the requirement of complex installation and connection of many wires, it is also easy to assemble and remains stable when in flight.

Independent IMU module
 

Extremely light weight with solid mechanical design

The aluminum alloy material and innovative mechanical design makes the gimbal extremely light weight (total 230g, GoPro Hero3 included). The structural design of the aluminum frame guarantees the strength of the gimbal.

Extremely light weight with solid mechanical design
 

Ideal Choice for Phantom and Flame Wheel

The mechanical design, weight and power supply will match the Phantom and Flame Wheel perfectly. The Phantom transmitter can be easily upgraded to give the pitch(tilt) control function of the gimbal, with a customized slider. No additional receiver channels are needed, it just uses the additional MC channels.

Ideal Choice for Phantom and Flame Wheel
 

Online Upgrade

The functionality can be easily updated by online firmware upgrades.

Online Upgrade

No customer comments for the moment.

Only registered users can post a new comment.

Search